Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths who have the proper equipment and technical know-how. They can design and program keys faster and cheaper than dealerships.
A dead coin battery is the most likely cause when your key fob stops locking or unlocking doors. There are other reasons the key could be malfunctioning.
Dead Coin Battery
A dead battery can stop your Peugeot 208 from locking and unlocking, and also hindering it from starting the engine. In this case you'll need to choose the alternate method to start described in your vehicle owner's manual.
Another reason the 208 won't start is because the spark plugs have been worn down. The spark plugs are responsible to ignite the fuel that starts the engine. However, replacement key for peugeot partner van have a limited time of life. They'll eventually fail if they're not used enough.
Luckily, there's an easy solution to this issue. The best solution is to determine the voltage of your car battery with a multimeter. If the voltage falls below 11,5 volts, it's time to replace it. If the battery is corroded, it is important to clean its contacts. This can be accomplished by removing the rubber cover from the two terminals on the battery and then using a wirebrush to clean any corroded battery parts. Then, you should connect your cables to connect the positive and negative poles.
Water Damage
If your 208 does not start and the battery hasn't gone flat, you should inspect the spark plugs. It could be that they are simply too dirty and do not spark. The spark plugs can be cleaned in the workshop.
Peugeot automobiles use a transponder key that works with the car's ignition system. This ensures that only a valid key is able to turn the engine. If the chip in the Peugeot key is damaged, it won't send the correct signal to the vehicle.
This is a typical issue that can be caused by water damage. This is especially prevalent in colder climates. the vehicle may have been exposed to rain or snow. If this is the case, you should contact a reputable auto locksmith who will have all the equipment and tools needed to reprogram the new key. They also have the most up-to-date technology and the machinery needed to make a Peugeot 208 smart key. The process shouldn't be more than 15 minutes.
Contacts to the battery are not working properly.
Peugeot changed from the old carbon-encased transponder chips to a new kind of chip that utilizes electronic components on circuit boards. The new system works great when it's brand new, but the circuit boards deteriorate over time and stop working properly.
This could prevent the immobiliser chip activating which means that your car won't start. Contact an Peugeot specialist or a locksmith, if this is the situation.
Another issue that is common is when the battery for the key fob gets depleted, which causes the blade of the key to stop being able to feed into the lock. A locksmith from your car will replace the battery and then cut a new key blade for you. This is a simple solution.
Faulty Receiver Module
If your Peugeot key fob isn't working after dropping it on the floor, or being exposed to a sudden rain or accidently washing it, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.
The key fob itself is fitted with rubber seals which prevent water from reaching the electronic chip inside. However prolonged exposure to water can cause damage to these seals and the chip. Submerging the key fob in the ocean at the beach or throwing it into the pool can be particularly damaging due to the high salt content.
The module will need to be replaced if your Peugeot spare key no longer works. This is only done by a skilled auto locksmith or Peugeot specialist. In contrast to other vehicles, Peugeot keys are protected by an immobilizer that is unique and requires the right coding to start the engine. This is the reason why you should only trust an experienced Peugeot locksmith with the task of creating and programming an alternative.
Computer malfunctioning on-board
The on-board computer in your Peugeot is the one responsible for all of the systems in your car, ranging from power windows to airbags. When something goes wrong with these systems, it'll typically display a code that identifies the problem. The code is stored within the system and remains there until the issue is resolved. This will often require the on-board computers to be replaced.
The most typical reason for the warning light for the airbag to come on is corroded or loose connections within the sensor. This can be caused by wear and tear, ageing, or exposure to moisture and salt. It is crucial to get this issue addressed as quickly as you can, since an airbag that is not functioning properly could be dangerous in the event of an accident.
If your Peugeot is showing a card that is not being detected error, the battery inside the key fob may be weak or dead. This can prevent the key fob from sending a signal that disables your vehicle's immobilizer. Try this by pressing the unlock button on the fob's key and then trying to start your car. If this does not work it is likely that the battery must be replaced.